500771-TX Muxlab DVI / USB2.0 KVM over IP PoE Extender

The KVM DVI over IP PoE Extender Kit allows DVI & USB equipment to be connected up to 330ft (100m) up to 1080p resolution @ 60Hz and 1920x1200 @ 60Hz via one (1) Cat5e/6 unshielded twisted pair cable in a point-to-point configuration. The Transmitter (500771-TX) and Receiver (500771-RX) also support PoE (PD) if used with a PoE (PSE) Ethernet Switch. The kit comes with one (1) Transmitter and one (1) Receiver. Additional Transmitters and Receivers may be purchased as kits or purchased separately depending on the number of units required.

Specifications

• Environment - DVI 1.0
• Devices - Computers and servers with DVI monitor ports
• Transmission - Transparent to the user
• Bandwidth - 300MHz
• Signals - DVI 1.0 protocol, HDCP 1.4
• Connectors
  • One (1) DVI receptacle
  • One (1) RJ45S for Cat 5e/6 unshielded or shielded twisted pair
  • Two (2) 3.5mm jacks for audio insert (on TX)/audio extract (on RX)
  • Two (2) 3.5mm jacks for mic-out (on TX)/mic-in (on RX)
  • One (1) 2.1mm locking barrel jack for power
  • One (1) or Four (4) USB Connector(s) for Host (on TX)/Client (on RX)
  • Four (4) DIP Switches for device ID addressing
• Maximum Distance - Cat5e/6: 330ft (100m) up to 1080p @ 60Hz and 1920x1200 @ 60Hz
• Latency - One (1) Frame (16ms) @ 60Hz (typical)
• Compression - JPEG 2000
• Network Bit Rate - 300Mbps (typical)
• Network Requirement - 1000BaseT with PoE
• RJ45 Pin Configuration - RJ45 Link
  • Pin 1 (R)
  • Pin 2 (T)
  • Pin 3 (R)
  • Pin 4 (R)
  • Pin 5 (T)
  • Pin 6 (T)
  • Pin 7 (R)
  • Pin 8 (T)
• Cable - One (1) Cat 5e/6 or better twisted pair cables required
• Power Source - This device supports PoE (PD), an external power supply is not included. It is intended to be powered via a PoE (PSE) Ethernet Switch. If required, an optional power supply (500993) may be purchased separately
• PoE - IEEE 802.3af
• Power Consumption
  • Transmitter: 2.85Watt
  • Receiver: 2.55Watt
• Temperature
  • Operating: 0° to 40°C
  • Storage: -20° to 85°C
  • Humidity: Up to 95% non-condensing
• Dimensions - 4.40” x 5.08” x 1.00” (112mm x 129mm x 25mm)
• Weight - 1.5 lbs (0.68kg)
• Compliance
  • Regulatory: FCC, CE, RoHS
  • Flammability: 94V0
• Warranty - 3 years
• Order Information - 500771-TX KVM DVI over IP PoE Extender TX (UPC: 627699907719)
• Accessories
  • 500920 16-Port Rackmount Transceiver Chassis
  • 500917 Wall Mount Transceiver Bracket Kit
  • 500993 Univ. Locking Power Supply 5VDC/2.6A US/UK/EU Blade

500771-TX Specifications PDF

500771-TX Manual