MAXFIT7F16APS Altronix Access Power Controller Kit, BC750 enclosure with eFlow104NB, ACMS8, VR6, PD16W

Altronix MaxFit7F16APS Access Power Controller distributes and switches power to access control systems and accessories. It converts a 120VAC, 60Hz input into sixteen (16) distributed 24VDC fuse protected outputs and sixteen (16) independently controlled 12VDC or 24VDC fuse protected relay outputs. Fail-Safe/Fail-Secure power outputs may be converted to dry form “C” contacts. Relays are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Keypad, Push Button, REX PIR, etc.

Specifications

Power Supply (eFlow104NB)

Input

• Voltage - 120VAC, 60Hz, 4.5A max
• Input Fuse - 6.3A/250V

Outputs

• Voltage - 24VDC @ 10A
• Auxiliary - 1A (unswitched)
• Other - Overvoltage protection, Filtered and regulated

Back-up Battery (not included)

• Type - Sealed lead acid or gel type
• Fuse Rating - 10A / 32VDC
• Failover - Upon AC loss, instantaneous

Fire Alarm Disconnect

• Supervised - Latching or non latching
• EOL - 10K Resistor

Supervision

• AC Failure - Form “C” contacts
• Battery - Form “C” contacts
• Low DC Power Shutdown - Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge

Indicators (LED)

• AC Input - 120VAC is present
• DC Output - Powered
• Battery - Discharged or not connected

Power Distribution Module (PD16W)

Input

• Voltage - 24VDC from eFlow104NB

Output

• Voltage - 24VDC
• Sixteen (16) fuse protected outputs
• 3.5A per output max
• Output Fuses - 3.5A/250V

Indicators (LED)

• Green LED - DC Output

Voltage Regulator (VR6)

Input/Output

• Voltage Range - 24VDC @ 10A = Output: 12VDC @ 6A

Output

• 12VDC regulated output
• Output rating 6A max
• Surge suppression

Indicators (LED)

• Input - Indicates input voltage is present
• Output - Indicates normal operating condition

Dual Input Access Power Controllers (Two (2) ACMS8)

Input

• Two (2) independent low voltage inputs
• Input Fuse: 15A/32V
• Trigger Inputs - Eight (8) individually controlled trigger inputs:
  • Normally open (NO) inputs
  • Normally closed (NC) inputs
  • Open collector sink inputs
  • Wet Input (5VDC - 24VDC) with 10K resistor
  • Any combination of the above

Output

• Fuse protected outputs rated @ 2.5A per output, non power-limited. Total output 20A max
• Eight (8) selectable 12VDC - 24VDC independently controlled outputs or eight (8) indepently controlled Form “C” relay outputs
  • Fail-Safe and/or Fail-Secure power outputs
  • Form “C” Relays. 28VAC or VDC @ 2.5A Rated
  • Auxiliary power outputs (unswitched)
  • Any combination of the above
• Any of the eight (8) fuse protected power outputs are selectable to follow power Input 1 or Input 2
• Individual outputs may be set to OFF position for servicing
• Output Fuses - 3A/32V each
• Total output current is determined by the power supply, not to exceed a maximum of 10A for each input

Fire Alarm Disconnect

• Supervised -Latching or non-latching, individually selectable for any or all of the eight (8) outputs
• EOL - 10K Resistor

Indicators (LED)

• Red LEDs - Outputs are triggered (relays energized)
• Blue LED - FACP disconnect is triggered
• Individual voltage LEDs
  • Green: 12VDC
  • Red: 24VDC

Physical and Environmental

• Dimensions (H x W x D) - 20.5” x 16.5” x 6.25” (520.7mm x 419.1mm x 158.8mm)
• Product / Shipping Weight (approx.) - 28.1 lb. (12.75 kg) / 34.1 lb. (15.5 kg)
• Operating Temperature - 0ºC to 50ºC (32ºF to 122ºF)
• Storage Temperature - -20ºC to 70ºC (-4ºF to 158ºF)
• Relative Humidity - 85% +/-5%
• BTU/Hr (approx.) - 145 BTU/Hr.

MAXFIT7F16APS Specifications PDF

MAXFIT7F16APS Manual